Ingalls 35880 Manuel d'utilisateur télécharger pdf

Ingalls

Product Installation Instructions ING35880-025009

Part Number 35880

CAUTION: Observe proper safety and repair procedures for installation of all chassis parts. Some chassis parts require specialized tools and

experience and therefore MUST be installed by a qualified technician otherwise an unsafe vehicle and/or personal injury could result. Wear

safety glasses and other protection.

WARNING: Before beginning, check for any damaged or loose suspension connections. Loose connections here indicate worn or broken parts

which MUST BE REPLACED. Failure to replace a damaged or worn spindle and/or link may cause the wheel to separate from the vehicle,

possibly resulting in serious personal injury.

NOTE: These parts are intended for use in vehicles with abnormal alignment and are designed to replace the non-adjustable factory equipment.

These parts are not designed for installation on vehicles with suspension and/or steering systems modified for racing, competition or any other

non-standard purpose.

Note for 35880: To minimize possible noise characteristics of polyurethane bushings, always lube with anti-seize, silicone, or naval grease

before installation.

1. IMPORTANT! Check alignment and document the readings. Determine the amount of rear camber change needed before

proceeding. This kit will provide –1.75° to +5.00° of camber change.

2. Raise the rear of the vehicle and support safely with jack stands and remove the two bolts that mount the upper control arm to the

body.

3. Install the U-shaped piece using the two provided hex head bolts so that the Ingalls logo faces down and the opening of the U faces

the wheel/tire assembly. Tighten to 70 lb-ft. (See Image #1)

4. Install the two adjusters using the remaining four bolts on each side so that the locating pins fit into the holes on the control arm

bushing bar and the slots line up with the threaded holes on the U-shaped piece. Using the four threaded holes marked “A” will

provide an adjustment range of -1.75° to +1.25° while using the holes marked “B” will provide +1.25° to +5.00° of camber adjustment.

5. Evenly tighten the four adjuster bolts to 40 lb-ft so that the adjusters are evenly seated on the control arm bushing bar. Set vehicle on

the ground and recheck camber. Adjust as required. (See Image #2)

6. NOTE: The bushing heat shield on the vehicle’s right side may need to be gently bent down to allow clearance to camber adjusting

kit.

7. Check for suspension clearance (see note below).

8. Verify camber readings and set rear toe to specifications. Road test and make modifications as necessary.

ALWAYS CHECK FOR SUSPENSION CLEARANCE

Modifying any suspension component may change other part clearances and cause binding or interferences. After installing any Ingalls’ product,

the suspension must be checked for binds or interference between all components, other arms and the chassis. Be sure that all control arms,

struts and steering ends move freely through the full movement of the suspension (springs may need to be removed to fully check component

travel). Installing any Ingalls’ product on a modified vehicle (lowered or raised) from the original factory design requires a detailed check of all

suspension components and their movements. Ingalls recommends that a trained technician install all products.

Limited Warranty

Subject to Disclaimer. All Ingalls products are warranted against defects in materials and workmanship for ninety (90) days from date of

purchase. During the warranty period, Ingalls will repair, or at its option replace at no charge, components that prove to be defective. The

product must be returned, shipping prepaid, to Ingalls facility. This limited warranty does not apply if the product is damaged by accident or

misuse. The foregoing warranty is in lieu of all other warranties expressed or implied including but not limited to any implied warranty of

merchantability, fitness, or adequacy for any particular purpose or use. Ingalls shall not be liable for any special, incidental or consequential

damages whether in contract, tort, or otherwise resulting from the use or the inability to use the product.

Warranty Disclaimer

Use of this product in competition, or use on vehicles altered from original manufacturer’s specifications or settings, EXPRESSLY VOIDS

WARRANTY. The user is urged to inspect for suspension binding or interference when the product is used in these manners. However, due to

the varying conditions and manner of use which the product will be subjected to in such uses, Ingalls Engineering Co., Inc. makes no warranties,

either express or implied, including any warranty of merchantability or fitness for a particular purpose for use in competition or with specifications

or settings other than those specified by the original manufacturer’s specifications.

DIAGRAM #1 IMAGE #1 IMAGE #2

Ingalls 1

Résumé du contenu

Page 1 - Ingalls

Ingalls Product Installation Instructions ING35880-025009 Part Number 35880 CAUTION: Observe proper safety and repair procedures for install

Commentaires sur ces manuels

Pas de commentaire

Ingalls 35880 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Ingalls 35880. Ingalls 35880 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Ingalls 35880